Modelling of PV - module based on data sheet parameters / V. T. Dinh ; sci. adv. A. V. Yurchenko, M. V. Kuimova

Уровень набора: (RuTPU)RU\TPU\conf\12353, Неразрушающий контроль: электронное приборостроение, технологии, безопасность, сборник трудов V Всероссийской научно-практической конференции студентов, аспирантов и молодых учёных, Томск, 25-29 мая 2015 г., в 2 т. / Национальный исследовательский Томский политехнический университет (ТПУ) = 2015Основной Автор-лицо: Dinh, V. T.Вторичный автор-лицо: Yurchenko, A. V., physicist, Professor of Tomsk Polytechnic University, candidate of technical sciences, 1974-, Aleksey Vasilievich, 727;Kuimova, M. V., linguist, Head of the Department of Tomsk Polytechnic University, Candidate of pedagogical sciences, 1976-, Marina Valerievna, 727Коллективный автор (вторичный): Национальный исследовательский Томский политехнический университет (ТПУ), Институт неразрушающего контроля (ИНК), Кафедра физических методов и приборов контроля качества (ФМПК);Национальный исследовательский Томский политехнический университет (ТПУ), Физико-технический институт (ФТИ), Кафедра иностранных языков физико-технического института (ИЯФТ)Язык: английский.Страна: Россия.Серия: Electrical Engineering and Non-Destructive TestingРезюме или реферат: The PV module is the interface, which converts light into electricity. Modelling of this device requires weather data (irradiance and temperature) as input variables. The output can be current, voltage, power. Any change in the inputs immediately leads to changes in the outputs. That is why, it is important to use an accurate model for the PV module. This paper presents a modelling of the effect of irradiance and temperature on the I-V and P-V characteristics of the PV module. The chosen model is a single diode model with both series and parallel resistors for greater accuracy. The modelling is simulated using Matlab/Simulink and Matlab/Guide software..Примечания о наличии в документе библиографии/указателя: [Библиогр.: с. 415 (2 назв.)].Тематика: труды учёных ТПУ | электронный ресурс | интерфейсы | свет | электричество | программное обеспечение | электрические характеристики Ресурсы он-лайн:Щелкните здесь для доступа в онлайн | Щелкните здесь для доступа в онлайн
Тэги из этой библиотеки: Нет тэгов из этой библиотеки для этого заглавия. Авторизуйтесь, чтобы добавить теги.
Оценка
    Средний рейтинг: 0.0 (0 голосов)
Нет реальных экземпляров для этой записи

Заглавие с титульного экрана

[Библиогр.: с. 415 (2 назв.)]

The PV module is the interface, which converts light into electricity. Modelling of this device requires weather data (irradiance and temperature) as input variables. The output can be current, voltage, power. Any change in the inputs immediately leads to changes in the outputs. That is why, it is important to use an accurate model for the PV module. This paper presents a modelling of the effect of irradiance and temperature on the I-V and P-V characteristics of the PV module. The chosen model is a single diode model with both series and parallel resistors for greater accuracy. The modelling is simulated using Matlab/Simulink and Matlab/Guide software.

Adobe Reader

Для данного заглавия нет комментариев.

оставить комментарий.