| 000 | 03107nlm1a2200457 4500 | ||
|---|---|---|---|
| 001 | 636401 | ||
| 005 | 20231030040133.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\356 | ||
| 090 | _a636401 | ||
| 100 | _a20131224a2011 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 102 | _aUS | ||
| 135 | _adrnn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aGain characteristics of large volume CuBr laser active media _fF. A. Gubarev [et al.] |
|
| 203 |
_aText _celectronic |
||
| 300 | _aTitle screen | ||
| 330 | _aThe paper presents the experimental results on how the active additive HBr and the temperatures of the containers with CuBr influence the gain characteristics of large volume (8 cm bore, 90 cm long) CuBr laser active media with the external heating of the active zone of the gas discharge tube (GDT). It has been demonstrated that an increase in the concentration of CuBr vapors results in the contraction of the gain profile of the active medium, consistent with the increase of the gain factor in the axial region of GDT. The contraction is also imposed by HBr addition. Despite the fact that we used the external heating of GDT at the pump power of 1.5 kW and less, the energy input is still not sufficient to produce the effective generation for large active volume lasers; and it is evident from the small gain profile width. The maximum gain profile width under experimental conditions (consider Pout/Pin > 2) was 3 cm; this value was obtained without HBr-additive within the active volume, while the concentration of CuBr vapors being significantly less than optimal, that corresponds to the maximum average lasing powerd | ||
| 333 | _aРежим доступа: по договору с организацией-держателем ресурса | ||
| 461 |
_tOptics Communications _oScientific Journal |
||
| 463 |
_tVol. 284, iss. 10-11 _v[P. 2565-2568] _d2011 |
||
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _alasers | |
| 610 | 1 | _aлазеры | |
| 610 | 1 | _ametal vapor laser | |
| 610 | 1 | _aлазеры на парах металлов | |
| 610 | 1 | _aсopper bromide | |
| 610 | 1 | _aбромид меди | |
| 610 | 1 | _aactive additives | |
| 610 | 1 | _aактивные добавки | |
| 610 | 1 | _acharacteristics | |
| 610 | 1 | _aхарактеристики | |
| 701 | 1 |
_aGubarev _bF. A. _cspecialist in the field of electronics _cAssociate Professor of Tomsk Polytechnic University, Candidate of physical and mathematical sciences _f1979- _gFedor Aleksandrovich _2stltpush _3(RuTPU)RU\TPU\pers\31657 |
|
| 701 | 1 |
_aTroitskiy _bV. O. |
|
| 701 | 1 |
_aTrigub _bM. V. _cspecialist in the field of non-destructive testing _cEngineer of Tomsk Polytechnic University _f1987- _gMaksim Viktorovich _2stltpush _3(RuTPU)RU\TPU\pers\31242 |
|
| 701 | 1 |
_aSukhanov _bV. B. _cspecialist in the field of electronics _cEngineer of Tomsk Polytechnic University _f1945- _gViktor Borisovich _2stltpush _3(RuTPU)RU\TPU\pers\31658 |
|
| 801 | 2 |
_aRU _b63413507 _c20140424 _gRCR |
|
| 856 | 4 | _uhttp://www.sciencedirect.com/science/article/pii/S0030401811000654 | |
| 942 | _cCF | ||