| 000 | 02919nla2a2200445 4500 | ||
|---|---|---|---|
| 001 | 639087 | ||
| 005 | 20231030040307.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\3485 | ||
| 035 | _aRU\TPU\network\3483 | ||
| 090 | _a639087 | ||
| 100 | _a20150220a2014 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 105 | _aa z 101zy | ||
| 135 | _adrcn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aResearch on the optimal cutting parameters for ball end finish milling process of complex surfaces _fO. B. Shamina, L. A. Belous, I. I. Ogol |
|
| 203 |
_aText _celectronic |
||
| 300 | _aTitle screen | ||
| 320 | _a[References: 7 tit.] | ||
| 330 | _aThe purpose of the present paper is to determine recommendations for complex surface finishing operation with ball end mill. The parameters that influence the roughness are: (i) technological parameters (such as step), (ii) geometrical (radius of milling cutter, angle of surface inclination or tilt angle) and (iii) cutting strategy. Paper presents roughness calculation theory and provide comparison of simulation and experimental data. Finally, recommendations to obtain desirable value of the roughness are given in the paper. | ||
| 333 | _aРежим доступа: по договору с организацией-держателем ресурса | ||
| 463 | 0 |
_0(RuTPU)RU\TPU\network\3200 _tMechanical Engineering, Automation and Control Systems (MEACS) _oproceedings of the International Conference, Tomsk, 16-18 October, 2014 _fNational Research Tomsk Polytechnic University (TPU) ; Institute of Electrical and Electronics Engineers (IEEE) _v[4 p.] _d2014 |
|
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _aball end finish milling | |
| 610 | 1 | _acomplex surface | |
| 610 | 1 | _acuttinl strategy | |
| 610 | 1 | _amilling | |
| 610 | 1 | _aroughness | |
| 610 | 1 | _aфрезерование | |
| 610 | 1 | _aсложные поверхности | |
| 610 | 1 | _aшероховатость | |
| 700 | 1 |
_aShamina _bO. B. _cspecialist in mechanical engineering _cassociate Professor of Tomsk Polytechnic University, candidate of technical Sciences _f1955- _gOlga Borisovna _2stltpush _3(RuTPU)RU\TPU\pers\33674 |
|
| 701 | 1 |
_aBelous _bL. A. |
|
| 701 | 1 |
_aOgol _bI. I. _cspecialist in mechanical engineering _cassistant of Tomsk Polytechnic University, programmer _f1984- _gIliya Igorevich _2stltpush _3(RuTPU)RU\TPU\pers\33675 |
|
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет (ТПУ) _bИнститут кибернетики (ИК) _bКафедра технологии автоматизированного машиностроительного производства (ТАМП) _h1607 _2stltpush _3(RuTPU)RU\TPU\col\18705 |
| 801 | 2 |
_aRU _b63413507 _c20161227 _gRCR |
|
| 856 | 4 | _uhttp://dx.doi.org/10.1109/MEACS.2014.6986952 | |
| 942 | _cCF | ||