| 000 | 03119nla2a2200397 4500 | ||
|---|---|---|---|
| 001 | 641289 | ||
| 005 | 20231030040423.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\6189 | ||
| 035 | _aRU\TPU\network\6188 | ||
| 090 | _a641289 | ||
| 100 | _a20150515a2015 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 105 | _ay z 100zy | ||
| 135 | _adrcn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aInfluence of Chip Formation Characteristics on Flank Contact Load Distribution in Titanium Alloy Cutting _fV. N. Kozlov, X. Li |
|
| 203 |
_aText _celectronic |
||
| 225 | 1 | _aMechanical Engineering, Processing and Surface Engineereng, Metals Treatment, Equipment and Tools | |
| 300 | _aTitle screen | ||
| 330 | _aIn this paper different contact conditions between tool, chip and work material are analyzed. Experimental and theoretical studies of contact load distribution on the artificial flank wear land of the cutter in free orthogonal turning of a disk made from titanium alloy (Ti-6Al-2Mo-2Cr) are described. Investigations of cutting with various feed rate and cutting speed show that the greatest contact loads are observed immediately at the cutting edge. It is associated with the discontinuous character of titanium alloy chip and the elastic recovery of the transient (machined) surface at the moment when generated chip element is separated. The main influence of the variable chip thickness ratio of the discontinuous chip on the value of the greatest normal contact load near the cutting edge is shown that confirms the author’ hypothesis about a sag of the transient surface in the cutting edge region. | ||
| 333 | _aРежим доступа: по договору с организацией-держателем ресурса | ||
| 461 | 0 |
_0(RuTPU)RU\TPU\network\5920 _tApplied Mechanics and Materials _oScientific Journal |
|
| 463 | 0 |
_0(RuTPU)RU\TPU\network\6028 _tVol. 756 : Mechanical Engineering, Automation and Control Systems (MEACS2014) _oInternational Conference, 16‐18 October, 2014, Tomsk, Russia _o[proceedings] _fNational Research Tomsk Polytechnic University (TPU) _v[P. 126-131] _d2015 |
|
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _aнагрузки | |
| 610 | 1 | _aизнос | |
| 610 | 1 | _aинструменты | |
| 610 | 1 | _aтитановые сплавы | |
| 700 | 1 |
_aKozlov _bV. N. _cspecialist in the field of mechanical engineering _cAssociate Professor of Tomsk Polytechnic University, Candidate of technical sciences _f1958- _gVictor Nikolayevich _2stltpush _3(RuTPU)RU\TPU\pers\32610 |
|
| 701 | 1 |
_aLi _bX. |
|
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет (ТПУ) _bИнститут кибернетики (ИК) _bКафедра технологии автоматизированного машиностроительного производства (ТАМП) _h1607 _2stltpush _3(RuTPU)RU\TPU\col\18705 |
| 801 | 2 |
_aRU _b63413507 _c20161229 _gRCR |
|
| 856 | 4 | _uhttp://dx.doi.org/10.4028/www.scientific.net/AMM.756.126 | |
| 942 | _cCF | ||