| 000 | 03219nla2a2200409 4500 | ||
|---|---|---|---|
| 001 | 646454 | ||
| 005 | 20231030040729.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\11590 | ||
| 035 | _aRU\TPU\network\11589 | ||
| 090 | _a646454 | ||
| 100 | _a20160301a2016 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 105 | _ay z 100zy | ||
| 135 | _adrcn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aStrength of Cutting Tool in Titanium Alloy Machining _fV. N. Kozlov, J. Y. Zhang |
|
| 203 |
_aText _celectronic |
||
| 225 | 1 | _aMechanical Engineering Technology | |
| 300 | _aTitle screen | ||
| 330 | _aIn this paper, contact conditions between cutting tool and work material, strength of cutting tool are analyzed. Experimental and theoretical studies of contact load distribution on the artificial flank wear-land that appears on the cutter in a free orthogonal turning disk of titanium alloy (Ti-6Al-2Mo-2Cr) are described. Calculations of internal stresses by the method of finite elements show that for the sharp cutter the main stresses into cutting wedge near to the cutting edge are compression stresses, very large (10 000 MPa) and exceed ultimate compression stress for cemented carbide. Decreasing of main stress with appearance of wear on the flank explains ability working of cutter even at large wear on the flank. Increasing of cutter’s break off probability with appearance of large wear on the flank is explained by increasing of zone where the internal stresses are large enough (more or equal 3 000 MPa) and increasing of defects probability into this zone, which serves as source of cracks. | ||
| 333 | _aРежим доступа: по договору с организацией-держателем ресурса | ||
| 461 | 0 |
_0(RuTPU)RU\TPU\network\11477 _tKey Engineering Materials _oScientific Journal |
|
| 463 | 0 |
_0(RuTPU)RU\TPU\network\11478 _tVol. 685 : High Technology: Research and Applications 2015 (HTRA 2015) _oThe IV International Conference, April 21-24, 2015, Tomsk, Russia _o[proceedings] _fNational Research Tomsk Polytechnic University (TPU) ; ed. N. V. Martyushev, A. M. Bogdan _v[P. 427-431] _d2016 |
|
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _aконтактные нагрузки | |
| 610 | 1 | _aпрочность | |
| 610 | 1 | _aрежущие инструменты | |
| 610 | 1 | _aизнос | |
| 610 | 1 | _aтитановые сплавы | |
| 700 | 1 |
_aKozlov _bV. N. _cspecialist in the field of mechanical engineering _cAssociate Professor of Tomsk Polytechnic University, Candidate of technical sciences _f1958- _gVictor Nikolayevich _2stltpush _3(RuTPU)RU\TPU\pers\32610 |
|
| 701 | 1 |
_aZhang _bJ. Y. |
|
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет (ТПУ) _bИнститут кибернетики (ИК) _bКафедра технологии автоматизированного машиностроительного производства (ТАМП) _h1607 _2stltpush _3(RuTPU)RU\TPU\col\18705 |
| 801 | 2 |
_aRU _b63413507 _c20160302 _gRCR |
|
| 856 | 4 | _uhttp://dx.doi.org/10.4028/www.scientific.net/KEM.685.427 | |
| 942 | _cCF | ||