| 000 | 03718nlm1a2200457 4500 | ||
|---|---|---|---|
| 001 | 655156 | ||
| 005 | 20231030041333.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\20974 | ||
| 035 | _aRU\TPU\network\18703 | ||
| 090 | _a655156 | ||
| 100 | _a20170706a2017 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 102 | _aUS | ||
| 135 | _adrcn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aAdhesion transfer in sliding a steel ball against an aluminum alloy _fS. Yu. Tarasov [et al.] |
|
| 203 |
_aText _celectronic |
||
| 300 | _aTitle screen | ||
| 320 | _a[References: p. 197-198 (14 tit.)] | ||
| 330 | _aHigh-temperature sliding experiments have been carried out to study both direct and back adhesion transfer between Al-Mg alloy metal and the ball bearing steel sample. It was shown that a transfer layer consisting of aluminum alloy formed on the trailing hemisphere of the steel ball. The amount of transferred metal increased with the test temperature from 25 to 200 °C. The periodical back transfer from the steel ball to the aluminum alloy disk was observed at the test temperature 100 °C. The wear groove bottom was characterized by the presence of large aluminum alloys transfer layer bulges, transfer layer film and plastically deformed subsurface layer. It was found that aluminum alloy transfer layer might accumulate on the trailing hemisphere of the ball and then could stick back to the wear groove surface of the disk. Such an adhesion transfer mechanism may be effective for metal transfer during friction sir welding by not threaded pins or pins fully covered by the transfer metal film. | ||
| 333 | _aРежим доступа: по договору с организацией-держателем ресурса | ||
| 461 | _tTribology International | ||
| 463 |
_tVol. 115 _v[P. 191–198] _d2017 |
||
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _aадгезия | |
| 610 | 1 | _aскольжение | |
| 610 | 1 | _aтемпература | |
| 610 | 1 | _aалюминиевые сплавы | |
| 610 | 1 | _aротационная сварка | |
| 610 | 1 | _aсварка трением | |
| 701 | 1 |
_aTarasov _bS. Yu. _cspecialist in the field of mechanical engineering _cProfessor of Tomsk Polytechnic University, Doctor of technical sciences _f1959- _gSergei Yulievich _2stltpush _3(RuTPU)RU\TPU\pers\31400 |
|
| 701 | 1 |
_aFilippov _bA. V. _cspecialist in the field of mechanical engineering _cassistant of Yurga technological Institute of Tomsk Polytechnic University _f1988- _gAndrey Vladimirovich _2stltpush _3(RuTPU)RU\TPU\pers\34612 |
|
| 701 | 1 |
_aKolubaev _bЕ. А. _cphysicist _cengineer of Tomsk Polytechnic University, Candidate of Physical and Mathematical Sciences _f1979- _gEvgeny Aleksandrovich _2stltpush _3(RuTPU)RU\TPU\pers\34115 |
|
| 701 | 1 |
_aKalashnikova _bT. A. _gTatiana Alexandrovna |
|
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет (ТПУ) _bИнститут физики высоких технологий (ИФВТ) _bКафедра физики высоких технологий в машиностроении (ФВТМ) _h2087 _2stltpush _3(RuTPU)RU\TPU\col\18687 |
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет (ТПУ) _bЮргинский технологический институт (филиал) (ЮТИ) _bКафедра технологии машиностроения (ТМС) _h356 _2stltpush _3(RuTPU)RU\TPU\col\18902 |
| 801 | 2 |
_aRU _b63413507 _c20170706 _gRCR |
|
| 856 | 4 | _uhttps://doi.org/10.1016/j.triboint.2017.05.039 | |
| 942 | _cCF | ||