| 000 | 03264nlm0a2200397 4500 | ||
|---|---|---|---|
| 001 | 657672 | ||
| 005 | 20231030041520.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\24324 | ||
| 090 | _a657672 | ||
| 100 | _a20180305d2018 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 105 | _ay z 100zy | ||
| 135 | _adrcn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aMechanical Treatment of ZrB2–SiC Powders and Sintered Ceramic Composites Properties _fS. P. Buyakova [et al.] |
|
| 203 |
_aText _celectronic |
||
| 300 | _aTitle screen | ||
| 320 | _a[References: 21 tit.] | ||
| 330 | _aThe effect of mechanical treatment by planetary ball milling on the properties of hot pressed ZrB2–SiC ceramics was studied. It has been shown that material densification after mechanical treatment is finished on initial stages of sintering process. Addition of SiC leads to essentially increasing of sample density up to 99% of a theoretical one for powder with 20% SiC, as compared with ZrB2 not higher when 76%. It has been shown that all defects which were accumulated during mechanical treatment are annealed during hot pressure process and there are no any changes of coherently diffracting domain (CDD) values in sintered ceramics. The model was suggested to describe of three-layered porous composite synthesis at the conditions of hot isostatic pressing and investigate the porosity evolution during synthesis. Model takes into account the conjugate heat exchange between sintered materials and walls of the reactor. | ||
| 463 |
_tResearch and Development - 2016 _oProceedings of the Scientific-Practical Conference, 14-15 December 2016 Moscow, Russia _v[P. 521-530] _d2018 |
||
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _aвысокие температуры | |
| 610 | 1 | _aдавление | |
| 610 | 1 | _aфрезерование | |
| 610 | 1 | _aмоделирование | |
| 701 | 1 |
_aBuyakova _bS. P. _cspecialist in the field of material science _cProfessor of Tomsk Polytechnic University, Doctor of technical sciences _f1968- _gSvetlana Petrovna _2stltpush _3(RuTPU)RU\TPU\pers\34758 |
|
| 701 | 1 |
_aKnyazeva _bA. G. _cRussian physicist _cProfessor of Tomsk Polytechnic University, doctor of physico-mathematical Sciences _f1962- _gAnna Georgievna _2stltpush _3(RuTPU)RU\TPU\pers\32712 |
|
| 701 | 1 |
_aBurlachenko _bA. G. _gAleksandr Gennadjevich |
|
| 701 | 1 |
_aMirovoy _bYu. A. _cspecialist in the field of material science _cAssistant of the Department of Tomsk Polytechnic University _f1992- _gYury Aleksandrovich _2stltpush _3(RuTPU)RU\TPU\pers\40241 |
|
| 701 | 1 |
_aKulkov _bS. N. _cspecialist in the field of material science _cProfessor of Tomsk Polytechnic University, Doctor of physical and mathematical sciences _f1952- _gSergey Nikolaevich _2stltpush _3(RuTPU)RU\TPU\pers\31428 |
|
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет _bИнженерная школа новых производственных технологий _bОтделение материаловедения _h7871 _2stltpush _3(RuTPU)RU\TPU\col\23508 |
| 801 | 2 |
_aRU _b63413507 _c20180305 _gRCR |
|
| 856 | 4 | _uhttps://doi.org/10.1007/978-3-319-62870-7_55 | |
| 942 | _cCF | ||