| 000 | 04031nla2a2200517 4500 | ||
|---|---|---|---|
| 001 | 661499 | ||
| 005 | 20231030041749.0 | ||
| 035 | _a(RuTPU)RU\TPU\network\32112 | ||
| 035 | _aRU\TPU\network\32109 | ||
| 090 | _a661499 | ||
| 100 | _a20191230a2019 k y0engy50 ba | ||
| 101 | 0 | _aeng | |
| 105 | _ay z 100zy | ||
| 135 | _adrcn ---uucaa | ||
| 181 | 0 | _ai | |
| 182 | 0 | _ab | |
| 200 | 1 |
_aImpact Toughness of Ti-6Al-4V Parts Fabricated by Additive Manufacturing _fM. Kazachenok [et al.] |
|
| 203 |
_aText _celectronic |
||
| 300 | _aTitle screen | ||
| 320 | _a[References: 5 tit.] | ||
| 330 | _aAdditive manufacturing is a new and quite promising trend in the low-cost building of Ti-6Al-4V parts which are widely used in aircraft, chemical, medical, and other industries. It is well-documented that 3D-printed Ti-6Al-4V parts have higher yield strength, ultimate tensile strength and hardness but lower ductility and toughness as compared with wrought alloy. In this study, comparison on the microstructure and impact toughness of wrought Ti-6Al-4V and ones fabricated by additive manufacturing such as i) laser and electron-beam powder bed deposition as well as ii) direct energy wire deposition was performed. The 2.7 times enhancement of fracture toughness of Ti-6Al-4V parts fabricated by electron beam free-form fabrication as compared with cast Ti-6Al-4V alloy was demonstrated. The 5.6 times increase in the impact toughness as in contrast with selective laser and electron-beam melted ones was revealed. | ||
| 333 | _aРежим доступа: по договору с организацией-держателем ресурса | ||
| 461 | 0 |
_0(RuTPU)RU\TPU\network\4816 _tAIP Conference Proceedings |
|
| 463 | 0 |
_0(RuTPU)RU\TPU\network\31884 _tVol. 2167 : Advanced Materials with Hierarchical Structure for New Technologies and Reliable Structures 2019 (AMHS'19) _oProceedings of the International Conference, 1–5 October 2019, Tomsk, Russia _fNational Research Tomsk Polytechnic University (TPU) ; Institute of Strength Physics and Materials Science SB RAS (Russia) ; eds. V. E. Panin ; S. G. Psakhie ; V. M. Fomin _v[020153, 4 p.] _d2019 |
|
| 610 | 1 | _aэлектронный ресурс | |
| 610 | 1 | _aтруды учёных ТПУ | |
| 610 | 1 | _aударная вязкость | |
| 610 | 1 | _aдетали | |
| 610 | 1 | _aаддитивное производство | |
| 610 | 1 | _a3D-печать | |
| 610 | 1 | _aтвердость | |
| 610 | 1 | _aрастяжения | |
| 610 | 1 | _aсплавы | |
| 610 | 1 | _aлазерное напыление | |
| 610 | 1 | _aслои | |
| 610 | 1 | _aпорошки | |
| 610 | 1 | _aосаждение | |
| 701 | 1 |
_aKazachenok _bM. |
|
| 701 | 1 |
_aPanin _bA. V. _cphysicist _cProfessor of Tomsk Polytechnic University, doctor of physical and mathematical Sciences _f1971- _gAlexey Viktorovich _2stltpush _3(RuTPU)RU\TPU\pers\34630 |
|
| 701 | 1 |
_aPanin _bS. V. _cspecialist in the field of material science _cProfessor of Tomsk Polytechnic University, Doctor of technical sciences _f1971- _gSergey Viktorovich _2stltpush _3(RuTPU)RU\TPU\pers\32910 |
|
| 701 | 1 |
_aVlasov _bI. V. _cspecialist in the field of material science _cEngineer of Tomsk Polytechnic University _f1988- _gIlya Viktorovich _2stltpush _3(RuTPU)RU\TPU\pers\33560 |
|
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет _bИнженерная школа новых производственных технологий _bОтделение материаловедения _h7871 _2stltpush _3(RuTPU)RU\TPU\col\23508 |
| 712 | 0 | 2 |
_aНациональный исследовательский Томский политехнический университет _bИнженерная школа ядерных технологий _bОтделение экспериментальной физики _h7865 _2stltpush _3(RuTPU)RU\TPU\col\23549 |
| 801 | 2 |
_aRU _b63413507 _c20191230 _gRCR |
|
| 856 | 4 | _uhttps://doi.org/10.1063/1.5132020 | |
| 942 | _cCF | ||